Opis artikla
Band-It - assembly example:
step 1:
Pull the buckle with ears to the tape end on the tape. Form clamps and place tape on tape. Pull the buckle over both tapes and bend the tape end approx. 30 mm under the buckle. When there are high loads on the clamps (e.g. for hose assembly) pull the tape twice through the buckle.
step 2:
Insert tape in the clamping tool from the side, press on the cam lever and tighten the crank clamps by rotating them. The maximum tension is reached when the tape can no longer be pulled under the buckle (this is easily "fulfilled" by applying a finger).
step 3:
After reaching the required tension, bend the tool slowly over the buckle. At the same time, loosen the crank by approx. a half rotation in order to prevent loss of tension and cracks in the tape. In order to crop the tape, pull the cutting lever backwards.
step 4:
Hit the tape onto the buckle with the hammer and fold both buckle ears over to secure the tape end.
Application:
for high loading, e.g. hose connections, tube fixations where high loading occurs
Assembly tool:
C001, C003
Materials:
rust-free stainless steel AISI 201 (1.4372) with fully rounded edges and high tensile strength (about 25% higher than 1.4401 or AISI 316)
Advantages:
•Stable as "normal" V2A for similar corrosion resistance - easily formed,
•patented imprint allows specific cutting to length of the strap and avoids waste,
•can be delivered in practical plastic container
step 1:
Pull the buckle with ears to the tape end on the tape. Form clamps and place tape on tape. Pull the buckle over both tapes and bend the tape end approx. 30 mm under the buckle. When there are high loads on the clamps (e.g. for hose assembly) pull the tape twice through the buckle.
step 2:
Insert tape in the clamping tool from the side, press on the cam lever and tighten the crank clamps by rotating them. The maximum tension is reached when the tape can no longer be pulled under the buckle (this is easily "fulfilled" by applying a finger).
step 3:
After reaching the required tension, bend the tool slowly over the buckle. At the same time, loosen the crank by approx. a half rotation in order to prevent loss of tension and cracks in the tape. In order to crop the tape, pull the cutting lever backwards.
step 4:
Hit the tape onto the buckle with the hammer and fold both buckle ears over to secure the tape end.
Application:
for high loading, e.g. hose connections, tube fixations where high loading occurs
Assembly tool:
C001, C003
Materials:
rust-free stainless steel AISI 201 (1.4372) with fully rounded edges and high tensile strength (about 25% higher than 1.4401 or AISI 316)
Advantages:
•Stable as "normal" V2A for similar corrosion resistance - easily formed,
•patented imprint allows specific cutting to length of the strap and avoids waste,
•can be delivered in practical plastic container
Lastnosti
| Izvedba | Zanka |
| Širina | 12,7 (1/2") |
Dodatne informacije o C254
| Teža | 7,9 g / Kos |
| GTIN | 4050571230210 |
| Embalažna enota | 100 Kos |
| Številka carinskega blaga | 73269098 |
| Skladno z RoHS | Da |
| Proizvajalec | Band-It |
YouTube videi:
Dokumenti
- Catalogue page Atlas 9 (Page 422) (PDF)
- Podatkovni list (Pogled za tiskanje)
- Podatkovni list (angleščina) (Pogled za tiskanje)
*packing unit: 100 units (Type C252: design similar to Valustrap)
Vse navedbe podatkov so nezavezujoče orientacijske vrednosti! Za izbiro podatkov, za katere ne izdamo pisnega potrdila, ne prevzemamo jamstev. Navedbe tlaka, v kolikor ni navedeno drugače, se nanašajo na tekočine skupine II. pri +20°C.
Možnosti plačila: